Smoke and carbon monoxide alarms are small devices with a large job: giving people time to get out when something goes wrong. In a rental property, they protect tenants, guests, and the home itself, and they are one of the simplest safety systems an owner can maintain. A working alarm costs little and takes minutes to test, yet a missing or dead alarm can turn a small incident into a serious one.
Owners should treat alarms as a system, not a single device. That means knowing where alarms are installed, testing them on a schedule, replacing batteries and aging units, and making sure tenants know what to do when an alarm sounds. The details depend on the property, the lease, and the rules that apply, so owners should check the requirements for their own home rather than assuming one setup fits every rental.
Where alarms belong in a rental property
Smoke alarms generally belong inside each bedroom, outside sleeping areas, and on every level of the home, including the basement. Carbon monoxide alarms belong where fuel burning appliances are used and near sleeping areas, following the manufacturer’s guidance and the rules that apply to the property. The exact placement depends on the layout, the heating system, and whether the home has an attached garage or gas appliances.
Testing, batteries, and replacement
Alarms should be tested regularly using the test button, and the result should be recorded. Tenants can be asked to test alarms between owner visits, but the owner should not rely on memory alone. A dated note in the property file, or a reminder in the maintenance schedule, keeps testing from being forgotten during a long, quiet tenancy.
Batteries need attention too. Replace them on a schedule the manufacturer recommends, and replace the entire alarm when it reaches the end of its service life, which the manufacturer usually prints on the unit. An alarm that chirps, gives false alarms, or fails a test should be replaced promptly rather than silenced and left in place. Dust and insects can also affect performance, so a gentle cleaning during inspections is a sensible habit.
What tenants should know
Tenants need clear instructions about alarms, and those instructions should be given at move in rather than after a problem. Explain where the alarms are, how to test them, who to call if one fails, and what to do when an alarm sounds. Tenants should also know that they should never remove an alarm or its battery to stop a nuisance alarm from cooking or steam, because that leaves the home unprotected.
The lease should state who is responsible for testing and battery replacement between owner visits, and the owner should confirm that responsibility in plain language at move in. When the lease is silent on the point, the owner should clarify it in writing and keep a copy. Clear expectations prevent the common situation where both sides assumed the other was handling the alarms.
- At move in: Show the tenant every alarm and how to test it.
- Testing: State how often alarms should be tested and who does it.
- Batteries: Say who replaces batteries and how to report a low battery warning.
- Problems: Give one clear contact for a failed or damaged alarm.
- Emergencies: Remind tenants to leave the home and call emergency services when an alarm sounds for a real fire or suspected carbon monoxide issue.
Checks during inspections and turnovers
Move in and move out inspections are the best time to verify every alarm. Test each unit, note its age and condition, replace batteries or units that are due, and photograph the alarms as part of the inspection record. A turnover is also the right time to confirm that no alarm was removed or damaged during the tenancy, and that any new appliance or layout change has not created a gap in coverage.
Keep records that show the work was done
Safety work is only useful if it can be shown. Keep a record of alarm locations, test dates, battery replacements, and unit replacements for each property. Photographs, receipts, and inspection notes together create a clear history that helps the owner, the manager, and any future buyer of the property understand what was maintained and when.
Make alarm checks a routine, not an afterthought
Smoke and carbon monoxide alarms work quietly for years, which is exactly why they are easy to neglect. A short checklist, a regular test, and a clear tenant conversation keep them ready for the moment they are needed.
Buckeye ARM manages long term rentals in Central Ohio and coordinates safety inspections and maintenance through property services and estimates. Owners who manage themselves can track alarm checks and other routines with property management software. A few minutes of attention per property is a small price for a system that protects the people inside.